Tekmar 262 Boiler Control Installation Manual de usuario descargar pdf (Pagina 11)

11 of 36

Sequence, Section C2

Internal Demand

(DHW SENS = DHW)

If the control receives a

DHW demand

from a DHW sensor attached to the

Com Sen

and the

DHW 10K

terminals (19 and 20), the

Boil TRG temperature is at least as hot as the DHW TANK setting plus 40˚F (22˚C).

DHW DURING UNOCCUPIED

The DHW operation during an

UnOccupied

period depends on the type of

DHW demand

that the 262 is receiving and the type of setback

that is being used. For this function to operate, the control must have the

Setback / None

DIP switch set to

Setback.

External Demand

(Aquastat )

If an external

DHW Demand

is used, the control can either continue operation of the DHW system as it would during the

Occupied

period or the control can ignore a call for DHW as long as the control is in an

UnOccupied

mode.

Internal Demand

(Sensor)

If an internal

DHW Demand

is used, a DHW TANK

Unocc

temperature can be set. This is the temperature that the tank maintains

as long as the control is in an

UnOccupied

mode.

Away

If the AWAY setting is made in the

Schd

menu, any

DHW Demand

is ignored and the tank cools off. Note: AWAY does not require

the DIP switch =

Setback.

Section C2 —DHW Priority (Mode = —1—)

DHW PRIORITY (DHW PRI = BOIL)

It is often desirable to limit or even stop the flow of heat to the heating

system when the DHW tank calls for heat. This allows for a faster recovery

of the DHW tank. If DHW PRI is set to Boil, the boiler pump (P1) is turned

off on a call for DHW. This setting is available only if DHW THRU = PUMP

has been selected as the DHW device. If a valve is used as the DHW

device, DHW priority can not be used. Caution should be taken to ensure

that the flow rate of the DHW pump is adequate for both the DHW tank and

the boiler(s), as this will be the only pump providing flow through the

boiler(s).

DHW PRIORITY OVERRIDE

To prevent the building from cooling off too much or the possibility of a

potential freeze up during DHW priority, the 262 limits the amount of time

for DHW priority. As the outdoor air temperature becomes colder, the

length of time that the 262 provides DHW priority is reduced. Once the

allowed time for priority has elapsed, the 262 overrides the DHW priority

and operates DHW and heating simultaneously.

CONDITIONAL DHW PRIORITY

If the boiler supply temperature is maintained at or above the required

temperature during DHW generation, this indicates that the boiler(s) has

enough capacity for DHW and possibly heating as well. As long as the

boiler supply temperature is maintained near its target, DHW and heating

occurs simultaneously.

DHW POST PURGE

After the

DHW Demand

is removed, the 262 performs a purge on the boiler(s). The 262 shuts off the boiler(s) and continues to operate

either the DHW pump or the DHW valve and the boiler pump. This purges the residual heat from the boiler(s) into the DHW tank. The

262 continues this purge for a maximum of four minutes or until the boiler supply water temperature drops 20˚F (11˚C) below the DHW

Boil TRG temperature. The 262 also stops the purge if the boiler supply temperature drops below the current Boil TRG temperature.

DHW MIXING PURGE

After DHW operation, the boiler(s) is extremely hot. At the same time, the heating zones may

have cooled off considerably after being off for a period of time. To avoid thermally shocking

the boiler(s) after DHW priority, the 262 shuts off the boiler(s), but continues to operate the

DHW while restarting the heating system. This allows some of the DHW return water to mix

with the cool return water from the zones and temper the boiler return water.

Outdoor air temperature

Increasing Air Temperature

Increasing Time

DHW priority demand time limit

DHW

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 35 36

Comentarios a estos manuales

Sin comentarios

Tekmar 262 Boiler Control Installation Manual de usuario Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Tekmar 262 Boiler Control Installation